This is your final notice

via IFTTT

Its gotten real bad

via IFTTT

The impossible solder job!

via IFTTT

Eggs falling from the sky

via IFTTT

History in a bag!

via IFTTT

Which hearing protection works best?

via IFTTT

What is a decibel and why is it important?

Decibel (dB) is a unit of measurement that describes the relative intensity or power of a sound. Decibel measurement is used to compare the loudness of different sounds and to quantify the degree of sound attenuation or amplification in various systems.

The decibel scale is logarithmic, which means that a small change in the sound pressure level corresponds to a large change in the perceived loudness. For example, an increase of 10 dB in sound pressure level represents a tenfold increase in sound intensity, and a doubling of loudness.
To measure sound in decibels, a sound level meter is typically used. This device has a microphone that converts sound waves into electrical signals, which are then analyzed and displayed as a numerical value in dB.
When measuring sound, the sound level meter takes into account the frequency of the sound wave and adjusts the measurement accordingly. This is because the human ear is more sensitive to some frequencies than others, and so a correction factor is applied to the measured sound pressure level to account for this.
In addition, when measuring the sound level in a particular location, the background noise level must also be taken into account. This is done by measuring the ambient noise level in the absence of the sound being measured and subtracting it from the total sound level.
Overall, decibel measurement provides a quantitative and objective way of comparing the loudness of different sounds and assessing the effectiveness of sound attenuation or amplification systems.

Decibels (dB) are used to express the ratio of two values, usually relating to power or intensity. The decibel scale is logarithmic, meaning that each increase of 10 decibels represents a tenfold increase in sound intensity.

The decibel scale is commonly used to measure sound levels, with the threshold of human hearing at 0 dB and sounds above 120 dB considered to be potentially dangerous to human hearing.

Some common noise measurement units include:

1. dBA: A-weighted decibels are used to measure sound levels in a way that more closely matches the sensitivity of the human ear to different frequencies.

2. dB SPL: Sound Pressure Level is a measurement of sound intensity in air, and is often used to measure noise levels in industrial or environmental settings.

3. dB(A) Leq: This measurement is used to measure average sound levels over a period of time, often in workplaces to assess noise exposure over an eight-hour workday.

Overall, decibels and the decibel scale are important tools for measuring and understanding sound levels and their potential impact on human hearing and health.

Decibel (dB) is a unit based on a logarithmic scale.

The decibel scale starts at 0 dB, which is the threshold of hearing for a healthy human ear. Sounds that are less than 0 dB are too quiet to be heard by most people. As the intensity of sound increases, the number of decibels also increases.

The formula for calculating decibels is:

dB = 10 x log10(I/I0)

Where I is the intensity of the sound being measured, and I0 is the reference intensity, which is usually set at 10^-12 W/m^2. This is the lowest intensity that can be detected by the human ear.

For example, if the intensity of a sound is 10 times greater than the reference intensity (I/I0 = 10), the number of decibels can be calculated as:

dB = 10 x log10(10) = 10 x 1 = 10 dB

The decibel scale is logarithmic, which means that every increase of 10 dB represents a tenfold increase in sound intensity. For example, a sound that is 80 dB is 10 times more intense than a sound that is 70 dB.

Decibel measurements are commonly used to measure the loudness of sound in a variety of settings, including music, engineering, and environmental noise pollution.

Decibel measurement is important for several reasons:

1. Hearing Protection: Exposure to high levels of sound can cause permanent hearing damage, and the decibel scale allows us to measure and monitor the loudness of sound to prevent hearing loss. For example, workplace safety regulations often require that employees wear hearing protection if they are exposed to sounds that are above a certain decibel level.

2. Environmental Noise: Decibel measurement is used to monitor and regulate environmental noise pollution, which can have negative impacts on health and quality of life. For example, cities may set noise ordinances to limit the volume of loud music, construction noise, or traffic noise in residential areas.

3. Audio Engineering: The decibel scale is used in audio engineering to measure and adjust the volume levels of music and other audio recordings. By using decibel measurements, engineers can ensure that sound levels are consistent and safe for listeners.

4. Communication: Decibel measurements are also important for communication, as they allow us to quantify and compare the loudness of different sounds. This is particularly useful in fields such as telecommunications, where it is important to ensure that signals are strong enough to be transmitted and received clearly.

Overall, decibel measurement is important for protecting our hearing, regulating environmental noise pollution, ensuring consistent audio quality, and facilitating clear communication.

It Was A Meltdown!

via IFTTT

I did this and saw smoke!

via IFTTT

Tornado watch!

via IFTTT

The first multitool?

via IFTTT